4" Inlet Oiled Cone Filter Short (Fits Cobra)
This is the same filter used in the 10th Gen Cobra Cold Air Intake. Why use a PRL Motorsports filter?
Our oiled filters are constructed from high quality, double layer cotton to increase the filtration surface by 10% - 15%. This causes air to move freely while maintaining superior filtration, trapping particles as small as 5 microns! The cotton filter is encased by coated steel mesh to ensure your PRL Motorsports air filter withstands the toughest of conditions!
Each filter is hand-molded using a flexible rubber base to ensure an airtight seal and absorb vibration. These filters do not use pressure-molding like other manufacturers, which can cause the rubber to seep into the filter element blocking airflow by up to 25%! Our air filters utilize a precision four-step process to virtually eliminate rubber seepage and maximize airflow!
Filter Dimensions:
- Inlet: 4.00"
- Total Height: 5.90"
- Filter Height: 5.00"
- Flange Height: 0.8"
- Base Diameter: 4.50"
- Top Cone Diameter: 4.00"
Filter Maintenance:
- PRE-CLEANING - Tap the filter or blow with air to remove excess dirt.
- APPLY CLEANER - Spray the filter with filter cleaner and allow the solution to soak in for about 15 minutes. * Never use strong detergents, high pressure water, or gasoline.
- RINSE - Rinse the filter with warm water, clean side to dirty side to flush out the dirt.
- DRYING - Allow the filter to dry naturally. Try to avoid heat because it might shrink the cotton.
- APPLY OIL - Re-oil the filter using filter oil by using 1 spray per 2 square inches of filter. Take care to not over-oil your filter. * Never use motor oil, transmission fluid, WD-40, or any other brand of filter oil as these may damage your filter.
This is the same filter used in the 10th Gen Cobra Cold Air Intake. Why use a PRL Motorsports filter?
Our oiled filters are constructed from high quality, double layer cotton to increase the filtration surface by 10% - 15%. This causes air to move freely while maintaining superior filtration, trapping particles as small as 5 microns! The cotton filter is encased by coated steel mesh to ensure your PRL Motorsports air filter withstands the toughest of conditions!
Each filter is hand-molded using a flexible rubber base to ensure an airtight seal and absorb vibration. These filters do not use pressure-molding like other manufacturers, which can cause the rubber to seep into the filter element blocking airflow by up to 25%! Our air filters utilize a precision four-step process to virtually eliminate rubber seepage and maximize airflow!
Filter Dimensions:
- Inlet: 4.00"
- Total Height: 5.90"
- Filter Height: 5.00"
- Flange Height: 0.8"
- Base Diameter: 4.50"
- Top Cone Diameter: 4.00"
Filter Maintenance:
- PRE-CLEANING - Tap the filter or blow with air to remove excess dirt.
- APPLY CLEANER - Spray the filter with filter cleaner and allow the solution to soak in for about 15 minutes. * Never use strong detergents, high pressure water, or gasoline.
- RINSE - Rinse the filter with warm water, clean side to dirty side to flush out the dirt.
- DRYING - Allow the filter to dry naturally. Try to avoid heat because it might shrink the cotton.
- APPLY OIL - Re-oil the filter using filter oil by using 1 spray per 2 square inches of filter. Take care to not over-oil your filter. * Never use motor oil, transmission fluid, WD-40, or any other brand of filter oil as these may damage your filter.
This is the same filter used in the 10th Gen Cobra Cold Air Intake. Why use a PRL Motorsports filter?
Our oiled filters are constructed from high quality, double layer cotton to increase the filtration surface by 10% - 15%. This causes air to move freely while maintaining superior filtration, trapping particles as small as 5 microns! The cotton filter is encased by coated steel mesh to ensure your PRL Motorsports air filter withstands the toughest of conditions!
Each filter is hand-molded using a flexible rubber base to ensure an airtight seal and absorb vibration. These filters do not use pressure-molding like other manufacturers, which can cause the rubber to seep into the filter element blocking airflow by up to 25%! Our air filters utilize a precision four-step process to virtually eliminate rubber seepage and maximize airflow!
Filter Dimensions:
- Inlet: 4.00"
- Total Height: 5.90"
- Filter Height: 5.00"
- Flange Height: 0.8"
- Base Diameter: 4.50"
- Top Cone Diameter: 4.00"
Filter Maintenance:
- PRE-CLEANING - Tap the filter or blow with air to remove excess dirt.
- APPLY CLEANER - Spray the filter with filter cleaner and allow the solution to soak in for about 15 minutes. * Never use strong detergents, high pressure water, or gasoline.
- RINSE - Rinse the filter with warm water, clean side to dirty side to flush out the dirt.
- DRYING - Allow the filter to dry naturally. Try to avoid heat because it might shrink the cotton.
- APPLY OIL - Re-oil the filter using filter oil by using 1 spray per 2 square inches of filter. Take care to not over-oil your filter. * Never use motor oil, transmission fluid, WD-40, or any other brand of filter oil as these may damage your filter.